Systematic Review for Comparison Type of Pulse Tube Refrigerator
Keywords:
: Pulse-Tubes-Refrigerator (PTR), Stirling Type Pulse Tube (STRP), Gifford McMahon Type Pulse Tube (GM)Abstract
A PTR (Pulse-Tubes-Refrigerator) is a cryocooler that could produce exceptionally low temperatures in one stage and even lower temperatures in two stages. Rather than utilizing the vapor compression cycle to achieve refrigeration, a PTR uses oscillatory compression and gas expansion within a closed space to obtain the required cooling. This paper discusses the significance of PTR and the many types of PTR. The most important feature of its primary varieties is recommended for large-scale cooling applications. Compared to Stirling pulse tube technologies, the equipment employed by GM pulse tube has been noted with low frequencies.
Downloads
References
Y. P. Banjare, R. K. Sahoo, and S. K. Sarangi, “CFD simulation and experimental validation of a GM type double inlet pulse tube refrigerator,” Cryogenics (Guildf)., vol. 50, no. 4, pp. 271–280, 2010, doi: 10.1016/j.cryogenics.2010.01.013.
G. Q. Lu and P. Cheng, “Numerical and Experimental Study of a Gifford-McMahon-Type Pulse Tube Refrigerator,” J. Thermophys. Heat Transf., vol. 17, no. 4, pp. 457–463, 2003, doi: 10.2514/2.6804.
M. Tendolkar, K. Narayankhedkar, and M. Atrey, Performance Comparison of Stirling-Type Single-Stage Pulse Tube Refrigerators of Inline and ‘U’ Configurations. 2008.
M. Avci and O. Aydin, “Second-law analysis of heat and fluid flow in microscale geometries,” Int. J. Exergy, vol. 4, no. 3, pp. 286–301, Jan. 2007, doi: 10.1504/IJEX.2007.013395.
“YP_Banjar_thesis”.
“a-review-of-pulse-tube-refrigerator-IJERTCONV4IS10026”.
C. Gu, Y. Zhou, J. Wang, W. Ji, and Q. Zhou, “CFD analysis of nonlinear processes in pulse tube refrigerators: Streaming induced by vortices,” Int. J. Heat Mass Transf., vol. 55, no. 25–26, pp. 7410–7418, 2012, doi: 10.1016/j.ijheatmasstransfer.2012.07.085.
“phasor analysis of GM-type pulse tube refrigerator”.
M. Baba, P. Kumar, and G. Kumar, “A Review on Pulse Tube Refrigerator,” 2021, pp. 433–445. doi: 10.1007/978-981-16-0942-8_42.
G. Popescu, V. Radcenco, E. Gargalian, and P. Bala, “Critical review of pulse tube cryogenerator research,” Int. J. Refrig., vol. 24, pp. 230–237, May 2001, doi: 10.1016/S0140-7007(00)00023-2.
A. Badgujar and M. Atrey, “Theoretical and experimental investigations on Stirling-type pulse tube cryocoolers with U-type configuration to achieve temperature below 20 K,” Proc. Inst. Mech. Eng. Part C J. Mech. Eng. Sci., vol. 229, no. 6, pp. 1112–1121, 2014, doi: 10.1177/0954406214542490.
B. Liu et al., “Numerical and experimental study on a Stirling/pulse tube hybrid refrigerator operating around 30 K,” Int. J. Refrig., vol. 123, pp. 34–44, 2021, doi: 10.1016/j.ijrefrig.2020.10.040.
J. Y. Hu, W. Dai, E. C. Luo, X. T. Wang, and Y. Huang, “Development of high efficiency Stirling-type pulse tube cryocoolers,” Cryogenics (Guildf)., vol. 50, no. 9, pp. 603–607, 2010, doi: 10.1016/j.cryogenics.2010.02.015.
Q. Cao et al., “Impedance magnitude optimization of the regenerator in Stirling pulse tube cryocoolers working at liquid-helium temperatures,” Cryogenics (Guildf)., vol. 58, pp. 38–44, 2013, doi: 10.1016/j.cryogenics.2013.09.007.
Z. Gan et al., “Study on a 5.0 W/80 K single stage Stirling type pulse tube cryocooler,” J. Zhejiang Univ. A, vol. 9, no. 9, pp. 1277–1282, 2008, doi: 10.1631/jzus.A0820220.
S. A. Potratz et al., “STIRLING-TYPE PULSE TUBE CRYOCOOLER WITH 1KW OF REFRIGERATION AT 77K,” vol. 985, pp. 42–48, 2008, doi: 10.1063/1.2908581.
Q. Cao et al., “Investigation on Precooling Effects of 4 K Stirling-Type Pulse Tube Cryocoolers,” J. Therm. Sci., vol. 28, no. 4, pp. 714–726, 2019, doi: 10.1007/s11630-019-1168-7.
L. Mohanta and M. Atrey, “Experimental Investigation of Single-Stage Inline Stirling-Type Pulse Tube Refrigerator,” Jun. 2022.
X. Chen, Y. Zeng, Z. Jiang, and Y. Cao, “Experimental study of single linear compressor driving two pulse tube refrigerators with adjusting valves,” Int. J. Refrig., vol. 88, pp. 291–299, 2018, doi: 10.1016/j.ijrefrig.2018.01.018.
H. Dang, “High-capacity 60K single-stage coaxial pulse tube cryocoolers,” Cryogenics (Guildf)., vol. 52, no. 4–6, pp. 205–211, 2012, doi: 10.1016/j.cryogenics.2012.01.006.
S. Zhu, Y. Kakimi, and Y. Matsubara, “Waiting time effect of a GM type orifice pulse tube refrigerator,” Cryogenics (Guildf)., vol. 38, no. 6, pp. 619–624, 1998, doi: https://doi.org/10.1016/S0011-2275(98)00026-5.
P. C. T. de Boer, “Optimization of the orifice pulse tube,” Cryogenics (Guildf)., vol. 40, no. 11, pp. 701–711, 2000, doi: https://doi.org/10.1016/S0011-2275(01)00003-0.
“Analysis of mass and energy flow rates in an orifice pulse-tube refrigerator1 F. Kuriyama * , R. Radebaugh National Institute of Standards and Technology, 325 Broadway, Boulder, CO 80303, USA”.
X. B. Zhang, L. M. Qiu, Z. H. Gan, and Y. L. He, “CFD study of a simple orifice pulse tube cooler,” Cryogenics (Guildf)., vol. 47, no. 5–6, pp. 315–321, 2007, doi: 10.1016/j.cryogenics.2007.03.005.
S. K. Rout, A. K. Behura, S. Dalai, and R. K. Sahoo, “Numerical Analysis of a Modified Type Pulse Tube Refrigerator,” Energy Procedia, vol. 109, pp. 456–462, 2017, doi: 10.1016/j.egypro.2017.03.067.
K. Wang, Q. R. Zheng, C. Zhang, W. S. Lin, X. S. Lu, and A. Z. Gu, “The experimental investigation of a pulse tube refrigerator with a ‘L’ type pulse tube and two orifice valves,” Cryogenics (Guildf)., vol. 46, no. 9, pp. 643–647, 2006, doi: 10.1016/j.cryogenics.2006.01.019.
P. Kittel, “Ideal orifice pulse tube refrigerator performance,” Cryogenics (Guildf)., vol. 32, no. 9, pp. 843–844, 1992, doi: https://doi.org/10.1016/0011-2275(92)90320-A.
A. Schor, “Design of a single orifice pulse tube refrigerator through the development of a first-order model,” Feb. 2008.
C. Wang, P. Y. Wu, and Z. Q. Chen, “Numerical analysis of double-inlet pulse tube refrigerator,” Cryogenics (Guildf)., vol. 33, no. 5, pp. 526–530, 1993, doi: https://doi.org/10.1016/0011-2275(93)90249-N.
M. Arslan et al., “Impact of Varying Load Conditions and Cooling Energy Comparison of a Double-Inlet Pulse Tube Refrigerator,” Processes, vol. 8, no. 3, p. 352, 2020, doi: 10.3390/pr8030352.
D. L. Gardner and G. W. Swift, “Use of inertance in orifice pulse tube refrigerators,” Cryogenics (Guildf)., vol. 37, pp. 117–121, 1997.
P. C. T. de Boer, “Performance of the inertance pulse tube,” Cryogenics (Guildf)., vol. 42, no. 3, pp. 209–221, 2002, doi: https://doi.org/10.1016/S0011-2275(02)00007-3.
W. Dai, J. Hu, and E. Luo, “Comparison of two different ways of using inertance tube in a pulse tube cooler,” Cryogenics (Guildf)., vol. 46, no. 4, pp. 273–277, 2006, doi: 10.1016/j.cryogenics.2005.11.023.
R. Radebaugh, M. Lewis, E. Luo, J. Pfotenhauer, G. Nellis, and L. Schunk, “Inertance Tube Optimization for Pulse Tube Refrigerators,” AIP Conf. Proc., vol. 823, Apr. 2006, doi: 10.1063/1.2202401.
S. Liu, X. Chen, A. Zhang, Z. Jiang, Y. Wu, and H. Zhang, “Investigation of the inertance tube of a pulse tube refrigerator operating at high temperatures,” Energy, vol. 123, pp. 378–385, 2017, doi: 10.1016/j.energy.2017.02.004.
B. Wang and Z. H. Gan, “A critical review of liquid helium temperature high frequency pulse tube cryocoolers for space applications,” Prog. Aerosp. Sci., vol. 61, pp. 43–70, 2013, doi: 10.1016/j.paerosci.2013.05.001.
Downloads
Published
How to Cite
Issue
Section
License
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.
All papers should be submitted electronically. All submitted manuscripts must be original work that is not under submission at another journal or under consideration for publication in another form, such as a monograph or chapter of a book. Authors of submitted papers are obligated not to submit their paper for publication elsewhere until an editorial decision is rendered on their submission. Further, authors of accepted papers are prohibited from publishing the results in other publications that appear before the paper is published in the Journal unless they receive approval for doing so from the Editor-In-Chief.
IJISAE open access articles are licensed under a Creative Commons Attribution-ShareAlike 4.0 International License. This license lets the audience to give appropriate credit, provide a link to the license, and indicate if changes were made and if they remix, transform, or build upon the material, they must distribute contributions under the same license as the original.
