Artificial Neural Network Model for Prediction of Tool Tip Temperature and Analysis

Authors

  • Sakir Tasdemir Selcuk University

DOI:

https://doi.org/10.18201/ijisae.2018637937

Keywords:

Artificial Neural Network, Prediction Model, Tool Tip Temperature, Turning

Abstract

Technological improvements put computer systems in the center of our life and various scientific disciplines. These can range from controlling a device in our home to public institutions and the industry. One of these disciplines is a sub-area in mechanical engineering called machining is concerned with not only mechanical systems but also computer aided systems. Artificial Neural Networks -an area of artificial intelligence- which is concerned with learning and decision making of computers is a field that scientists are very interested in. In this study, an Artificial Neural Network (ANN) system was designed for predicting the temperature at the tool tip during the machining process. In the metal cutting process, tool tip temperature is one of the conditions that must be identified, analyzed and monitored along with the main cutting force. For this purpose, an ANN model was developed to determine The Tool Tip Temperature (TTT) in the turning process. In the designed ANN model, parameters consisting of three inputs and one output were used. The three input variables were rake angle (γ-o), approaching angle (c-o), feedrate (f-mm/rev) respectively. The output parameter was the TTT (T-0C). The most appropriate model was determined according to Mean Squared Error (MSE) ration. In the test phase of the ANN, the smallest MSE was obtained with the model formed as 3-5-1. In this network settings, calculations were MSE=0.00144, R2=0.9956 (absolute fraction of variance) in the training phase and MSE=0.00231, R2=0.9954 in the test phase. The results show that the designed ANN model can be used for predicting and analyzing tool tip temperature.

Downloads

Download data is not yet available.

References

Demir H., Özlü B., Sertleştirilmiş 30MnVS6 Mikroalaşımlı Çeliğin Kesme Kuvvetleri Ve Yüzey Pürüzlülüğü Açısından İşlenebilirliğinin Araştırılması, Erciyes Üniversitesi Fen Bilimleri Enstitüsü Dergisi, 2009, 25, 262 – 271.

Tasdemir, S. (2012). Artificial neural network based on predictive model and analysis for main cutting force in turning. ENERGY EDUCATION SCIENCE AND TECHNOLOGY PART A-ENERGY SCIENCE AND RESEARCH, 29(2), 1471-1480.

Taşdemir Ş., Neşeli S., Sarıtaş İ., Yaldız S., Prediction of Surface Roughness Using Artificial Neural Network in Lathe, International Conference on Computer Systems and Technologies CompSysTech’08, 12-13 June,2008, Technical University-Gabrovo, Bulgaria.

Saglam H, Unsacar F, Yaldiz S. Investigation of the effect of rake angle and approaching angle on main cutting force and tool tip temperature. International Journal of Machine Tools & Manufacture 46, 2006, 132–141.

Saglam, H., Yaldiz, S., & Unsacar, F. (2007). The effect of tool geometry and cutting speed on main cutting force and tool tip temperature. Materials & Design, 28(1), 101-111.

Karagüzel, U., Bakkal, M., Budak, E. Frezeyle tornalama işleminde kesme sıcaklığı modeli ve deneysel olarak doğrulanması. 6. Ulusal Talaşlı İmalat Sempozyumu, 5-7 Kasım 2015, İstanbul.

Duran, A., Turgut, Y., Günay, M. (2011). Tornalamada Oluşan Takım-Talaş Ara Yüzey Sıcaklığının Pirometre ile Deneysel Olarak Ölçülmesi. Politeknik Dergisi, 14(4).

Brito, R.F., Carvalho, S.R., Lima e Silva, S.M.M.,Ferreira, J. R., “Thermal Analysis in Coated Cutting Tools”, International Communications in Heat and Mass Transfer, 36, 314–321 (2009).

Korkut, I., Acır, A., Boy, M., “Application of Regression and Artificial Neural Network Analysis in Modelling of Tool–Chip İnterface Temperature in Machining”, Expert Systems with Applications, 38, 11651–11656 (2011).

Radulescu, R., Kapoor, S. G. (1994). An analytical model for prediction of tool temperature fields during continuous and interrupted cutting. Journal of engineering for industry, 116(2), 135-143.

Mia, M., & Dhar, N. R. (2016). Response surface and neural network based predictive models of cutting temperature in hard turning. Journal of advanced research, 7(6), 1035-1044.

Karpat Y, Ozel T. Predictive analytical and thermal modeling of orthogonal cutting process—Part I: Predictions of tool forces, stresses, and temperature distributions. J Manuf Sci E 2006;128(2):435–44.

Liang, L., Xu, H., & Ke, Z. (2013). An improved three-dimensional inverse heat conduction procedure to determine the tool-chip interface temperature in dry turning. International Journal of Thermal Sciences, 64, 152-161.

Sharma, P., Sidhu, B. S., & Sharma, J. (2015). Investigation of effects of nanofluids on turning of AISI D2 steel using minimum quantity lubrication. Journal of cleaner production, 108, 72-79.

Davoodi, B., & Tazehkandi, A. H. (2014). Experimental investigation and optimization of cutting parameters in dry and wet machining of aluminum alloy 5083 in order to remove cutting fluid. Journal of Cleaner Production, 68, 234-242.

Al Masud, A., Ali, S. M., & Dhar, N. R. (2011, January). Modeling of Chip Tool Interface Temperature in Machining Steel-An Artificial Intelligence (AI) Approach. In Proceedings of the 2011 international conference on industrial engineering and operations management Kuala Lumpur, Malaysia.

Mia, M., & Dhar, N. R. (2017). Optimization of surface roughness and cutting temperature in high-pressure coolant-assisted hard turning using Taguchi method. The International Journal of Advanced Manufacturing Technology, 88(1-4), 739-753.

Ozkan, I. A., Saritas, I., & Yaldiz, S. (2009, May). Prediction of cutting forces and tool tip temperature in turning using Artificial Neural Network. In 5th Int. Adv Tech Symp, Karabuk, Turkey (pp. 13-15).

Kider, M. S. (2016). Tornalama işleminde kesme parametrelerinin karşılaştırmalı optimizasyonu (Yüksek Lisans Tezi, Selçuk Üniversitesi Fen Bilimleri Enstitüsü).

Yalçın, Ü., (2008). Talaş Kaldırma Sırasında Oluşan Sıcaklık Ve Termal Yorulma Faktörlerinin Takım Aşınma Davranışlarına Etkisi (Doktora Tezi, Gazi Üniversitesi Fen Bilimleri Enstitüsü).

Arda, E., (2012). Kesici takımlarda dahili soğutma yönteminin geliştirilmesi ve kesme işlemine etkisinin incelenmesi (Yüksek Lisans Tezi, Sakarya Üniversitesi Fen Bilimleri Enstitüsü).

Tasdemir, S., Yaniktepe, B., & Guher, A. B. (2017). Determination of Wind Potential of a Specific Region using Artificial Neural Networks. International Journal of Intelligent Systems and Applications in Engineering, 5(3), 158-162.

Tumer, A. E., Koc, B. A., & Kocer, S. (2017). Artificial Neural Network Models for Predicting The Energy Consumption of The Process of Crystallization Syrup in Konya Sugar Factory. International Journal of Intelligent Systems and Applications in Engineering, 5(1), 18-21.

Sertkaya, A.A, Ates., A., Altınışık, K. (2016). Designing of Open Cell Aluminum Foam Heat Exchanger and Modelling of its Thermal Performance by Using Ann Method, page: 31-37. Politeknik Dergisi, 19(1).

Downloads

Published

29.03.2018

How to Cite

Tasdemir, S. (2018). Artificial Neural Network Model for Prediction of Tool Tip Temperature and Analysis. International Journal of Intelligent Systems and Applications in Engineering, 6(1), 92–96. https://doi.org/10.18201/ijisae.2018637937

Issue

Section

Research Article